Filler for distillation column. Do you know what a tsarga is and how to make it? The volume of the cube for the distillation column

23.02.2022

To get a high-quality alcoholic drink at home, you need the right equipment. A classic distillation cube is not enough for these purposes, since fusel oil vapors and volatile ethers enter the product along with alcohol vapors.

It is they who give moonshine a nasty smell, addiction and a hangover headache.

A radically new step in home brewing is the appearance of column-type apparatuses.

Important! On the distillation cube instead of a steamer is installed tsarga- a hollow tube stuffed with a fine stainless steel mesh or covered with small pieces of metal of a spiral-prismatic shape.

The essence of the improvement is in the principle of reflux.

Dephlegmation - the deposition of vapors and their flow into the cube:

An important process takes place in the tsarga - the "alignment" of vapors on the floors.
The lighter the pairs, the higher in the king they are able to break through.
We need heavy smelly fusel vapors to settle down, and pure alcohol vapors to rise up, where the selection unit is located.

The video tells in more detail what a tsarga is and why it is needed in a moonshine still:

Kinds

Tsarga is the basis for beer and film distillation columns. It is tubular and plate-shaped. The physics of phenomena in these devices is different.

In a tubular king vapors turn into condensate on the walls and surface of the nozzle. Vapors freely return back to the cube, evaporating along the way. The mechanism of heat and mass transfer works.

The minus of this tsarga is the great length, bulkiness and complexity of building phlegm by levels.
Plus - the simplicity of the device.

In a plate-shaped king vapors settle on the surface of the mesh. The vapors coming from below pass through the accumulated phlegm layer, bubbling occurs.

Phlegm passes light vapors, heavy vapors remain in liquid form. There can be from 3 to 12 plates, depending on the diameter and type of the side.

The downside of this drawer is the complexity of manufacturing, the need for glass sections to control bubbling and the level of reflux on the plates.
Plus - compact size, the highest quality products.

Nuances

For a skilled craftsman, making a tsarga with his own hands is not a problem.

To get a great thing, we need:

Materials. Copper is better processed, but very expensive. Stainless steel will require the help of an argon welder, but stainless steel pipes are much easier to find. Brass plumbing joints are perfect as a connector for copper pipes, it is better to connect stainless steel with clamps.
Tools. A roller pipe cutter will help to cut the pipe evenly, but it is not available to everyone. Therefore, we use the "grinder", sandpaper for cleaning burrs. To solder copper pipes, you will need a gas burner, solder and flux. Stainless steel will have to be welded either with a TIG machine or with special electrodes for stainless steel.
Skills. It is not difficult to solder copper pipes - the theory of soldering can be found on specialized sites or from bloggers. Working with stainless steel is more difficult - it is very easy to make a hole when welding with an electrode, and welding with a non-consumable electrode in an argon environment requires experience and skill. Before carrying out work, it is better to practice on scraps or unnecessary pieces.

How to do it yourself?

Making a good wash or distillation column is a rather complicated and troublesome business. If it is possible to purchase a reliable and tested device from the manufacturer, the result will be more predictable.

The factory-made device is often not available due to the high cost. Making a tsarga with your own hands is more accessible and cheaper.

Calculation of length and diameter

Different capacities require the use of different pipe diameters and lengths.

Reference! For distillation - obtaining raw alcohol - a pipe 0.5 - 1 meter long is suitable. The diameter is not that important.

For rectification, the parameters of the tsarga depend on the required performance, heater power, cube volume. There are extensive formulas for calculations, as well as standard solutions. For a 3 kW, 40 liter cube, you will need a 1.5 meter long drawer with a minimum diameter of 3 inches.

For a home master, the most affordable will be the manufacture of a tubular side. It consists of the following elements.

Frame

Can be used as a thin-walled stainless steel or copper pipe.

Important! The use of conventional pipes, plastic or aluminum is undesirable - an aggressive "cocktail" of chemical compounds can lead to the destruction of the pipe and impurities in the final product.

The use of heat-resistant laboratory glass is justified if there is a need for visual control over processes. Glass is difficult to process, very fragile, but absolutely not subject to chemical destruction.

The body is best made cranked - a composite of 2-3 parts. This will make cleaning easier, and will also allow you to achieve different results.

Connections

There are several ways to connect pipes.

plumbing thread. The simplest and cheapest method. With each assembly, the knee columns are “twisted” with tow or fum-tape. Minus - the bulkiness of the method
Butt couplings - "American". Flat flares are compressed by threaded nuts. The pipes are sealed with gaskets, they will have to be replaced with silicone ones - they are not damaged by an aggressive environment.
Clamp clamps. Pipes at the joints have extensions, which are wrapped around with cone clamps. The most convenient and quick connection. Popular, but harder to find on sale.

Netting for stuffing

So that the spiral prismatic packing does not spill out into the distillation cube, you need to make a restrictive mesh at the bottom of the side.

The main property of this mesh is that it should be thick and made of thin stainless steel wires. So the cross section of the pipe will not decrease.

The use of a plate with drilled holes as a limiter will significantly degrade the parameters of the column.

Work progress

We select the pieces of pipes we need. They should be the diameter we need - from 24 to 60 mm. The productivity of the apparatus and the quality of the outgoing products depend on the diameter.

Cut pipes to size.

Important! The ends must be even, an oblique cut can lead to an inclination of the device, which will affect the quality of the entire system.

Solder with tin solder or weld connectors. It is better to use clamps - they are more reliable.

We make a grid-limiter for SPN (spiral-prismatic nozzle). We need a piece of pipe and a mandrel, 1-2 mm in diameter. thinner. We insert a mesh into the pipe, press it with a mandrel - we get a cylinder from the mesh.

The tsarga is going from bottom to top along the knees:

A limiter is placed for the nozzle, the first knee is attached to the cube.
The nozzle is filled up, after which the next knee is installed.
After using the tsarga, be sure to wash it with caustic soda and a brush.

Warming

Depending on the technology used, the tsarga needs to be insulated.

If normal distillation takes place, the lining is not needed to be insulated. It will be difficult to improve the result during rectification without insulation.

As a heater, you can use sanitary couplings made of foamed polyethylene, trays made of expanded polystyrene. You can fasten with disposable clamps or wire.

Watch a video in which an experienced moonshiner tells how to properly insulate a drawer:

Place of the device in the distiller

Moonshine stills are of various types. The drawer is not required to obtain raw alcohol, a steamer and a cooler are enough.

Reference! To obtain noble distillates or pure alcohol, a distillation column is indispensable. In this case, sampling units, coolers, bypass valves, temperature and pressure sensors are attached to the drawer.

The tsarga is not just a pipe. The main processes take place in it - the separation of alcohol vapors into fractions, as well as heat and mass transfer - the basis for obtaining high-quality alcoholic beverages at home.

The drawer is not just a pipe between a cube and a refrigerator (reflux condenser). From the correct choice of geometric dimensions, material and thermal insulation of the side depends on the productivity, degree of purification, technological modes of distillation and comfortable work with the apparatus as a whole.

Tsarga for moonshine still

In a simple classical distillation, drawers are successfully displacing dry steamers. Solving the problem of combating splashing, the tsargs allow you to simultaneously deal with sulfurous gases, strengthen moonshine, and even to some extent purify the drink from non-volatile compounds due to partial condensation. Another advantage of the drawer is that the equipment becomes less bulky.

The diameter of the drawer is chosen based on the desired performance and the maximum speed of the steam, at which the resulting wild phlegm and splashes that have flown out of the cube along with the steam flow back unhindered, and not be driven up the walls to the refrigerator.

At a steam speed in the side up to 2 m/s, spray is excluded, from 2 to 3 m/s the result is somewhat worse, and at 3 m/s and above, the steam begins to drive phlegm up the pipe.

V = N * 750 / S (m/s),

N - power (kW);
750 - steam generation (cm3 / s kW)
S is the cross-sectional area of the column along the inner diameter (mm 2).

To protect against splashing, in most cases, the height of the drawer is sufficient within 30-40 cm, therefore, only geometric considerations are decisive when choosing a height. Usually proceed from the free vertical placement of the refrigerator to ensure the best conditions for its operation.

The correct length of the moonshine still (classic distiller) is approximately equal to the length of the refrigerator.

Material

Standard drawers are made of copper or stainless steel. Copper acts as a catalyst and helps bind sulfurous gases, clearing moonshine of unwanted odors. The use of copper is advisable in the distillation of cereals and some fruit and berry brews in order to obtain noble distillates by repeated fractional distillation.

The copper side does not provide advantages in the distillation of sugar or any other raw material for further distillation or obtaining NDRP in apparatus with liquid extraction, since non-condensable gases and vapor in the condenser find different paths. The gas flies out through the TCA (atmospheric communication tube) and does not come into contact with the condensate going to the extraction, and therefore does not dissolve in it. Purification of sulfur dioxide on such devices is simple and does not require additional efforts.

Sometimes, to increase the effect during the first distillation, a copper nozzle (filler) is used. This is a rather controversial technique: the contact area with copper will grow, the purification from sulfurous gases will improve, but at the same time the productivity of the apparatus will decrease, which means that the distillation time will increase, as a result of prolonged boiling of the mash, more other harmful impurities will be released. The measure is important here: if you choose copper rings or tubes as a nozzle, this is one thing, and if you choose a dense nozzle like SPN, it’s completely different.

Dense nozzles have a place in the second stage, at the first stage it is better to limit yourself to just a copper side.

Drawer for distillation and beer columns

When choosing the size of the drawer side for heat and mass transfer processes on mash or distillation columns, the conditions are somewhat greater, but they are understandable and natural.

Inner diameter

The cost of the column as a whole significantly depends on the diameter. Increasing the diameter not only increases the cost of the pipes from which the column is made, but also increases the amount of packing required. And the nozzle is one of the most expensive components of the device. For example, for a column one and a half meters high with an inner diameter of 38 mm, 1.7 liters of nozzle are needed, for 48 mm - already 2.7 liters.

The performance of the column is directly proportional to the square of the internal diameter of the side. With an increase in diameter from 38 to 48 mm, productivity will increase by one and a half times. Therefore, choosing, for example, between pipe 52 with a wall of 1 mm or 1.5 mm, you need to understand that the nominal withdrawal rate for the first will be 1800, and for the second - 1700 ml / h. Here is such a price for a seemingly insignificant change in size.

The nominal heating power in Watts and the nominal rate of removal of the “body” milliliters per hour are numerically equal to the cross-sectional area of the drawer, based on the inner diameter. This rule is true when used as a SPN packing, the size of which corresponds to the diameter of the column. For other less or denser nozzles, the numerical values will be different, but the general trend will continue.

The denser the packing, the lower the performance of the column will be. True, this is compensated by a better separating ability. If we talk about SPN and rectification, then the optimal size of the nozzle should be 12-14 times smaller than the inner diameter of the side. When getting fortified moonshine or NRLP, the cleaning requirements are much lower, so a larger nozzle can be used, shifting the focus towards performance.

Height

It is the height of the mounted part of the tsarg that largely determines the separating ability of the column. Do not confuse this indicator with the height of the tsargi. Manufacturers often mislead buyers with their unsuccessful designs. For example, the height of the drawer is 40 cm, but of these, the lower empty space is 5 cm, another 3 cm is taken by the structure to support the nozzle, and on top - a device for fixing the nozzle 2 cm high and an empty place for foam to the reflux condenser - 5 cm. As a result nozzles in 40 cm tsarge is not 40 cm, but only 25 cm! Even if you put three of them in a row, you won’t get rectified alcohol.

The same applies to the use of one tsargi 1.5 meters long or three 50 cm each. At first glance, there is no difference, but if you take a closer look and calculate the height of the attachment part, then everything is not so simple.

For a clear division into fractions and separation of the “heads”, the nozzle part must be at least 1 meter high, and the height of one side must be no more than 1.5 meters.

With a shorter length, the separating ability will be insufficient for a clear selection of "heads". The limitation of 1.5 meters is due to the fact that the efficiency of the packed column changes unevenly with increasing height. For example, increasing the length from 50 to 60 cm will give the same increase in separation power as from 120 to 150 cm (figures are arbitrary and are given to show the trend). The height of the nozzle part in one side should be no more than 30 of its internal diameters.

The benefit of a further increase in height is negated by the channel and wall effects. If you want to build a higher column, you need to divide it into several tsargs or use phlegm concentrators - devices that divert phlegm from the walls and direct it to the center of the nozzle. But the use of concentrators often leads to early choking of the column, especially with inept performance. And if there are grids in the design, then in most cases choking becomes a regularity.

Phlegm concentrators

Influence of the height of the drawer side on technological indicators

Suppose that there are well-insulated and vertically exposed two-inch columns 1.2 and 1.8 meters long. Increasing the height of the column by 1.5 times will increase the volume of distilled bottom bulk by the same one and a half times, since the holding capacity and volume of the packing will increase. It will be possible later to proceed to the selection of "tails", significantly reducing their volume. But you have to pay for everything - the selection time will increase, as well as the volume of “heads” and “head restraints”.

In order to "feel" the order of numbers, here is a table with the volumes and time of selection of various fractions during the distillation of 40 liters of moonshine:

The rate of "body" withdrawal will be almost the same, and the transition temperature from "body" to "tails" withdrawal will change from 94-95 degrees to 97. However, this will depend on the sense of smell of the column operator. In both cases, a product of approximately the same quality will be obtained.

The wall thickness of the column should be within 1-1.5 mm. Such a thickness is thermally transparent and makes it possible to measure temperatures with a negligibly small delay. If temperature sensors are attached with aluminum tape to the surface of the columns under thermal insulation, this will be enough for normal process control.

Increasing the wall thickness will only increase the cost and weight of the column. This makes the design less stable and imposes additional requirements on the strength of the cube lid.

The correct choice of the dimensions of the drawer is not difficult, it is only necessary to take into account their influence on the technological parameters of the process and compliance with the tasks set.

Even if the funds allow, it is important to avoid the most important mistake - megalomania.

With an increase in diameter, not only productivity changes. Small diameter columns (25-30 mm) require special attention. It is problematic to use a nozzle in them, to center the phlegm flowing down from the reflux condenser, and in general to achieve at least a confident cut-off of the “tails”, not to mention the retention of intermediate impurities.

Columns of medium diameter (35-55 mm) are calm and balanced, work clearly and predictably.

Large diameter columns (more than 57 mm) are more difficult to set up for stable operation, they are productive, but are subject to various sores that nullify the benefit of increased speed. Large columns suffer from spontaneous channel formation: when a standard power is supplied, the pressure in the cube does not increase, and the column does not choke. When changing the packing to a smaller one, everything stabilizes, but the performance becomes the same as that of much smaller columns. Therefore, columns, starting from a diameter of 57 mm, are equipment for experienced distillers who want creativity.

There are many models of moonshine stills of various designs on sale - with dry steamers, bubblers, distillation columns and other effective equipment. But what to do if you have a moonshine still of an old design, but it is made soundly, and you just don’t raise your hand to throw it away? The advice is simple - upgrade.

The role of the tsarga is to remove high-boiling oily substances from the mash vapors under the common name - fusel. It is these impurities that spoil the taste of moonshine and its aroma. The drawer in an industrial moonshine can theoretically make it possible to obtain fairly pure raw alcohol after the first distillation, but this device should not be idealized.

Many articles provide data that a drawer with a length of 15 cm gives a 20-fold degree of cleaning, 35 cm - 50-fold and 45 cm - 65-fold, without explaining what it is - the frequency of cleaning. Many people think that the resulting moonshine becomes 20, 50 or 65 times cleaner. This is not entirely true. The frequency of cleaning shows how many times the mutual contact of the condensate inside the drawer with the nozzle and the vapor phase occurs.

Naturally, the higher the multiplicity, the better the cleaning. But in a household moonshine still, both an industrial and a do-it-yourself tsarga will make it possible to get moonshine three to four times cleaner after the first distillation than without it. Is it worth it to upgrade the device? Certainly yes. Having tried the product obtained from the apparatus using the tsarga, you will be convinced of this. Repeated distillation will further strengthen you in the opinion that such a fairly simple device can radically change your idea of \u200b\u200bwhat homemade moonshine is.

How to make a do-it-yourself king

There is nothing complicated in the process of making the tsargi. Even a person who has ever held a grinder, a soldering iron and a drill in his hands is able to make the simplest version of this device. It is better if the master knows how to work on a lathe or weld stainless steel. Threading stainless steel by hand is quite difficult, almost impossible. But if you find dies marked R18 or R18F2, then you can try.

What is required for work? Depending on which version of the tsargi you choose. If there is a tendency to experiment, then you can make the tsarga collapsible, consisting of several parts. If you just want to try whether what they say about the role of the tsargi in moonshine is true, then you can make one fragment. The design provides for the possibility of increasing the length in any case.

So, let's start making the tsargi with our own hands. For this you need:

A piece of pipe with a diameter of 35 - 45 mm made of stainless steel, copper or brass. Ordinary steel, cast iron and plastic are not suitable. The first metal will rust very quickly, cast iron is heavy and such pipes are not found, and plastic is unsafe in contact with alcohol vapors. It will not ignite or melt, but such compounds may be formed that no chemist can establish their composition, and it will be difficult for doctors to diagnose.

In addition to the pipe, you will need a threaded fitting, which must be fixed to the lid of the distillation cube using two clamping nuts on silicone gaskets. Rubber is not recommended, unless you can find a heat-resistant one. If the lid of the cube is made of stainless steel, then the fitting can be welded on.

From this fitting, we will begin work. On the side, you need to cut the internal thread so that it can easily be wound onto the pipe. If you made an internal thread on the fitting, then you cut the external one on the body of the drawer. When working with your own hands, such liberties are allowed.

The length of the thread is at least 3 cm. It should be noted that the entire upper part of the device will be held on it. If the drawer for the moonshine still serves as the base of the distillation column, then lateral loads are not expected. But if a side pipeline with a refrigerator is connected to it, then it is desirable that the base be strong.

There should also be a thread on the top of the tsarga. We will connect the outlet of the steam line to the refrigerator, the second section of the drawer or the head of the rectification column to it. We choose the lower part of the tsarga with a length of 35 - 40 cm. If necessary, it is very easy to lengthen it. If there is a thread, you can use any of the known methods for connecting two pipes - an American, a coupling, etc.

Below, 2-3 cm from the edge of the upper thread, we drill a hole with a diameter of 3-4 mm and screw into it, having previously cut the thread, a piece of tube 3-4 cm long - a socket for the thermometer probe. There it will be inserted during operation using a silicone seal.

Seat for thermometer

In the tsarga, the most important thing is not the mechanical method of connection, but its inner part. The volume of the drawer is filled with metal wire spirals - nozzles. Their diameter is 2 - 3 mm, visually they resemble small springs. They are made from stainless steel or copper.

You need a lot of them and it's impossible to do it yourself. It is best to buy special filling on specialized sites. To prevent the filler from waking up inside the tank, a fine mesh of stainless steel or copper is inserted into the lower part of the body of the drawer. It can be cut from an old kitchen strainer, or donated to a new one.

As a last resort, use a dishwashing net, but you only need to choose stainless steel. We push several such meshes inside the pipe and seal them. An even better option is to buy a regular Panchenkov wire nozzle. This is a strip of stainless steel woven, which is twisted into a spiral and tightly inserted into the body of the tsarga.

To some, all these fillers may seem like overkill, but it is they who turn an ordinary pipe into a drawer. It works not only as a filter - the most complex physical and chemical processes of interaction between steam and a condensing liquid take place inside, as a result of which the steam is divided into packet fractions and purified from all kinds of impurities.

When using the drawer, it should be taken into account that the speed of distillation will decrease by 30 percent. But the time spent is compensated by the quality of the product.

The process of home brewing is simple in terms of technology. The quality of the final product depends on the performance of the apparatus in which the process takes place. To improve them, you will need additional modules. One of them is a drawer for a moonshine still.

The difference between moonshine and sivukha is the degree of purification. If the mash is poorly cleaned, then the output is a product containing fusel oils. These impurities give the drink an unpleasant smell, taste, and also reward the consumer with a headache in the morning.

Tsarga removes fusel oils from alcohol vapors. What is a tsarga in a moonshine still, any experienced distiller knows. This device helps to make the final product several times purer after the first distillation.

The need for installation

Why do we need a tsarga in a moonshine still for home brewing? Every moonshiner who distills for himself at home understands that the purity of the product is the key to quality. A distillation drawer on an industrial scale helps to get raw alcohol, but for the home you can use a simpler device.

In addition to cleaning, the tsarga gives strength to the final product. At the exit, you will get a drink several degrees stronger than classic moonshine.

The principle of operation of the king

The principle of operation of the drawer of the moonshine still is similar to that of the steamer. Both devices work by condensing vapors with different boiling points. The tsarga works according to the following scheme:

The steam turns into condensate and flows off the module head.
Vapors move towards the condensate. The speed directly depends on the length of the device. The longer, the better the cleaning.
The condensate feeds the vapors.

Since heat exchange is ongoing, the cleaning process does not stop.

Functions and structural features of the column

The king has another name -. But there is a big difference because it has a filler. In fact, the tsarga itself is a column that is installed above the distillation cube. The filler can be a copper wire spiral or a simple stainless steel washcloth. The last option is preferable.

The result is a completely full-fledged filter that will help bring the strength of the drink to 60 °, as well as clean it with high quality.

Like any filter, from time to time the side is removed and cleaned. Otherwise, the output will be a tasteless drink with a pungent odor.

How does a column work?

The tsarga is 15, 35 and 45 centimeters long. Accordingly, it cleans differently. Degree of purification - 20, 50, 60-fold. It is allowed to use several drawers on one moonshine still, which will further enhance the cleaning effect.

When cleaning, the condensed liquid passes back into the cube, and purified alcohol enters the refrigerator. In any case, the use of a tsarga at the exit gives a product that is several times stronger and cleaner than just a moonshine still.

Can a dryer be replaced?

Technically, of course, it is possible. But from the point of view of the final product, you should not do this. Tsarga is several times more effective. The maximum degree of cleaning with the help of a steamer is 20%, and with the help of a drawer - 60. Despite the fact that the principle of operation is similar, the drawer is much more efficient and allows you to get a higher degree of cleaning and strength of moonshine. Do-it-yourself steamer at a cost will not be cheaper. And if you can not see the difference in price, then why neglect the quality. Therefore, experts argue that it is not necessary to replace the tsarga with a dry steamer.

Does it need to be insulated?

Warming is a contentious issue. Each of the distillers himself decides how much it is necessary. There are supporters of insulation who claim that this increases productivity. But many, on the contrary, argue that the modules must be cooled and even create special drafts near the device. Therefore, insulation is an individual matter for each distiller. You can insulate both the drawer and the distillation cube.

How to do it yourself?

For home brewing, you can make a tsarga with your own hands. It does not require complex technical skills. You can create a collapsible module from several parts. A do-it-yourself drawer for a moonshine still will be much cheaper than buying a ready-made module. At the same time, the quality of homemade products will be even higher than the technical details. Anyone who has basic knowledge and skills can make a module. Of course, it is ideal if a person knows how to handle a lathe, since it is difficult to cut threads on stainless steel by hand.

The assembly algorithm is as follows:

We attach the conductor to the top of the pipe.
We turn the pipe over and place it at the bottom of another conductor.
We attach the distiller from above.
From the bottom, measure 3.5 cm, then drill a hole in the pipe.
Install the probe from the digital thermometer.
We put stainless steel washcloths into the pipe and fix the sieve at the bottom.

Everything, the homemade module is ready, start making an alcoholic drink that is safe for health.

Necessary materials

To make this module with your own hands, you will need:

Pipe. Best option for stainless steel. This material is resistant to alcohols, oils and other substances. The pipe should be 35–45 cm.
Conductor for fastening to the limiter.
Sieve.
30 ordinary household washcloths.
Elastic band from a medical dropper.

A set of material is inexpensive, and therefore the final cost of a home-made module will please.

Filler manufacturing

You buy the filler on special sites or in stores, but it can also be easily made on your own. The best option is washcloths from hardware stores. To prevent objects from crumbling and falling out, a grid with small cells is necessarily fixed from below. Washcloths are recommended to be cut and then twisted into spirals. It is recommended to fill the pipe completely, but do not compress it.

If there are voids, the process will be inefficient. You can check it with a simple tap.

Home brewing is a legal process. You can freely pamper your family for the holiday with pure alcohol without a sharp taste and smell. In order for the drink to be strong and fairly clean, the apparatus should be finalized. You can use a sukhoparnik, but it is better to make a tsarga. The material for manufacturing is simple, the process itself is also not difficult. As a result, the user will receive an improved device that produces crystal clear and strong moonshine.

People involved in moonshine are aware of the release of fusel oils (a by-product of the distillation of mash, a viscous liquid with a pungent odor) during the distillation of mash.
Various absorbers are used to reduce the amount of oil release and a cleaner distillation of the mash. Let's define such a strange term as absorption - this is the transfer of components (atoms) of a gas mixture into the volume of the condensed phase in contact with it. And the absorber is an element (filler) of the apparatus, on the surface of which the absorption process takes place. It should be noted that during the process, selective absorption of one or more components from the gas mixture by liquid absorbers occurs.
There are two types of nozzles: random (we just put them in the drawer, due to their small size) and regular (placed in the equipment in a special way)
In the role of absorbers in home brewing, the following are used: RPN Panchenkov nozzle, Selivanov nozzle (or spiral prismatic nozzle), Rashig rings.
The use of nozzles allows us to achieve a high distillation result and thus reduces the cleaning time.
Let's consider them in more detail separately.

And the first thing we start with is quite popular - On-load tap-changer Panchenkov nozzle, is a wire nozzle. It is used in tsargo-type distillers to improve purification, alcohol vapor is filtered through a nozzle, while depositing fusel oils and impurities from the mash on the grid.
The undoubted advantage of this nozzle is the possibility of its regulation in the side, i.e. we can roll it up to the density we need, and take it out of the apparatus for cleaning precipitated fusel oils.
The nozzle is made of food stainless steel.
You can buy a Panchenkov nozzle on our website

Next comes Selivanov nozzle, which is a spiral prism (made of wire materials). Designed to install a distillation column in the tsarga, it acts as a contact device. Usually nozzles of this type are made of copper and stainless steel. The nozzle is reusable and can serve as a filler for any tsarga.

And the last of the stated nozzles in this discussion is Raschig rings. This nozzle belongs to the regular type of nozzles. It has a cylindrical shape with a thin wall, and the outer diameter is equal to the height of the ring. Size range: from 25 mm to 150 mm. Most often, rings made of ceramics are used (a variation of porcelain is possible), carbon-graphite ones are found, and less often steel ones.

A small remark - nozzles. used to clean moonshine during the distillation process are not the know-how of recent years. They have been used in the chemical and petroleum industries for quite a long time (panel nozzles are another type), having proven themselves in this direction only from the best side. Therefore, relying on proven cleaning methods, the nozzles gradually entered the moonshine industry.